Backstory: my Kindle Voyage had issues refreshing screen, sometimes pressing along the bottom helped. So I took off the back cover, disconnected and reconnected all the connectors. And now it forgot it's a Kindle. When connected to computer it just shows itself for a moment as
Freescale Semiconductor, Inc. SE Blank MEGREZ
for a moment, then disappears again.
so I tried that. Running
sudo imx_usb uboot_2009-08-lab126_wario_usb_fastboot.bin
config file <./disp5021//imx_usb.conf>
vid=0x066f pid=0x3780 file_name=mx23_usb_work.conf
vid=0x15a2 pid=0x004f file_name=mx28_usb_work.conf
vid=0x15a2 pid=0x0052 file_name=mx50_usb_work.conf
vid=0x15a2 pid=0x0054 file_name=mx6_usb_work.conf
vid=0x15a2 pid=0x0061 file_name=mx6_usb_work.conf
vid=0x15a2 pid=0x0063 file_name=mx6_usb_work.conf
vid=0x15a2 pid=0x0071 file_name=mx6_usb_work.conf
vid=0x15a2 pid=0x007d file_name=mx6_usb_work.conf
vid=0x15a2 pid=0x0080 file_name=mx6ull_usb_work.conf
vid=0x1fc9 pid=0x0128 file_name=mx6_usb_work.conf
vid=0x15a2 pid=0x0076 file_name=mx7_usb_work.conf
vid=0x1fc9 pid=0x0126 file_name=mx7ulp_usb_work.conf
vid=0x15a2 pid=0x0041 file_name=mx51_usb_work.conf
vid=0x15a2 pid=0x004e file_name=mx53_usb_work.conf
vid=0x15a2 pid=0x006a file_name=vybrid_usb_work.conf
vid=0x066f pid=0x37ff file_name=linux_gadget.conf
vid=0x1b67 pid=0x4fff file_name=mx6_usb_sdp_spl.conf
vid=0x0525 pid=0xb4a4 file_name=mx6_usb_sdp_spl.conf
vid=0x1fc9 pid=0x012b file_name=mx8mq_usb_work.conf
vid=0x1fc9 pid=0x0134 file_name=mx8mm_usb_work.conf
vid=0x1fc9 pid=0x013e file_name=mx8mn_usb_work.conf
vid=0x3016 pid=0x1001 file_name=mx8m_usb_sdp_spl.conf
config file <./disp5021//mx6_usb_work.conf>
parse ./disp5021//mx6_usb_work.conf
Trying to open device vid=0x15a2 pid=0x0063
Interface 0 claimed
HAB security state: development mode (0x56787856)
== work item
filename ./personal/uboot_2009-08-lab126_wario_usb_fastboot.bin
load_size 0 bytes
load_addr 0x00000000
dcd 1
clear_dcd 0
plug 1
jump_mode 3
jump_addr 0x00000000
== end work item
No DCD table
loading binary file(./personal/uboot_2009-08-lab126_wario_usb_fastboot.bin) to 00980000, skip=0, fsize=1d364 type=aa
<<<119652, 119652 bytes>>>
succeeded (security 0x56787856, status 0x88888888)
jumping to 0x00980400
do_command err=-7, last_trans=0
do_command err=-7, last_trans=0
do_command err=-7, last_trans=0
do_command err=-1, last_trans=0
do_command err=-1, last_trans=0
config file <./disp5021//mx6_usb_work.conf>
parse ./disp5021//mx6_usb_work.conf
Trying to open device vid=0x15a2 pid=0x0063status failed
Interface 0 claimed
do_command err=-1, last_trans=0
do_command err=-1, last_trans=0
do_command err=-1, last_trans=0
do_command err=-1, last_trans=0
do_command err=-1, last_trans=0
Is this the path I should follow now? Time to do some soldering, or are there things I could try before?
On 99% you have flash memory damaged. Without replacing it, you will not do anything. It will probably be easier and cheaper to replace the motherboard.
